ETS-Lindgren Model 2090 Controller Drivers Download

Download Now
ETS-Lindgren Model 2090 Controller Driver

Ask for a quote on a Used ETS Lindgren Miscellaneous Controllers from Axiom Test Equipment at today. A pneumatic cylinder is used to change polarization, and can be remotely controlled using an optional ETS-EMCO Model Controller or an ETS-EMCO. MODEL NAME .. ETS-Lindgren. NCR. NCR. Multi-Devices. Controller. ETS-Lindgren. OPT1. NCR.

ETS-Lindgren Model 2090 Controller Update

Type: Driver
129 (3.89)
Downloads: 1055
File Size: 21.35Mb
Supported systems: Windows All
Price: Free* [*Free Regsitration Required]

Download Now
ETS-Lindgren Model 2090 Controller Driver

Driver for ETS-Lindgren Model 2090 Controller

The antenna is constructed of lightweight, corrosion-resistant aluminum, providing years of trouble-free service. All elements are attached with knurled knobs for easy assembly.

What's missing? Tell us about it.

The included wheeled pedestal permits horizontal and vertical antenna polarization, and tilt-angle adjustments. Without size reduction, the longest dipole element length would be approximately 7.

The antenna features a specially-designed feed to handle high power requirements of up to 5 kW for generating high electric field strength. A hairpin matching stub is used to improve the low-frequency VSWR, which minimizes mismatch loss between the amplifier and antenna.

Continuous Rotation Multi-Axis Positioning System (MAPS )

Make sure the power is off and secured before proceeding. The branch circuit supplying power to the motor bases must be protected from excess current according to local electrical codes.

Integral circuit protection is provided in the motor base assembly. Make sure the conductor size is adequate for the motor load and the distance from the mains source. Improperly sized conductors will lead to a high voltage drop in the power conductors and cause reduced starting torque and premature motor failure. ETS-Lindgren Model 2090 Controller motor base assembly is provided with ETS-Lindgren Model 2090 Controller IEC power inlet for connecting to the mains.

Connect the fiber optic control cable and install the power connection according to local electrical code. See the controller manual for information on connecting the fiber optic cable. After the fiber optic cable is installed, secure it with a wire tie to one of the leveling screws. Electrical Installation 19 20 This page intentionally left blank. The installation must be performed by factory installation specialists or individuals ETS-Lindgren Model 2090 Controller by ETS-Lindgren to perform installation.

ETS-Lindgren Controller : Manual

This information provided in this manual is intended to be used only by those installation specialists. See the assembly drawings located in the back pocket of the manual to assist with installation. Remove the absorber from the floor and lower wall areas prior to ETS-Lindgren Model 2090 Controller to avoid damage to the absorber. Locate the reference point.

It is generally located along the bore sight axis of the range antenna. See Bore Sight and Leveling on page 27 for additional information regarding bore sight. With permanent ETS-Lindgren Model 2090 Controller, place an X on the floor of the chamber at the reference point. Draw a in 1.

The diameter is larger than the actual perimeter of the circular anchor plates for the turntable, and should only be used as a guide in centering the turntable portion of the MAPS. Before removing fiber optic cables from the motor base, label the replacement locations for accurate reconnection. Remove the wood deck. See assembly drawing located in the back pocket of the manual for details.

ETS-Lindgren Model 2090 Controller

The drive units are designed to move from the shipping container to the chamber floor as a single unit. If you cannot move it as a single unit without causing damage, separate the upper drive unit.

ETS-Lindgren Model 2090 Controller Driver Windows XP

When installing the turntable on modular shielding, do not drill anchor holes through the floor joint strips. Use the shim plates provided.

ETS-Lindgren Model 2090 Controller 64 BIT

Insert the shim plates to level the turntable over the vault seams. Screw the anchor plates to the floor using 14x1 square socket flat head screws.

  • ETS-Lindgren Controller User Manual pages
  • Download ETS-Lindgren Model Controller Firmware for OS Independent
  • ETS-Lindgren EMC Antennas ATEC Rentals
  • ETS-Lindgren 2090 Controller User Manual
  • 2090 technology
  • EMCO/ETS-Lindgren 2090 Multi-Device Positioning Controller

Drill pilot holes for these screws, and make sure to vacuum shavings to provide good contact with the floor.

Related Posts

  • Clevo M550G Keyboard Driver Windows Clevo M550G Keyboard Driver Windows

    clevo laptop and notebook batteries at cheap and discount price. 71 · mah MBAT-6 clevo MG MV laptop Battery: $ Clevo MG MV MG MV MG MV M54 M55 M M Battery,Price: RM,End time 3/7/ AM MYT. Keyboards Clevo MTU Keyboards · Internal memory Clevo MTU Internal memory · Harddisks Clevo MTU Harddisks · Solid State Drives (SSD) Clevo. Type: ...

  • Duxbury External ISDN (DX128) Modem New Duxbury External ISDN (DX128) Modem New

    Results 1 - 48 of 49 - Motorola BitSURFR Pro external ISDN Modem. Modem ha a standard DB25 serial port. SN# matches box & the modem! General  Missing: Duxbury ‎(DX). There are drivers for Duxbury Networking Modem of all modifications on this page Duxbury Networking External ISDN (DX) modem (Utility included) driver. This external USB ISDN adapter can work at ...


    Intel® Desktop Boards DQ35JO and DQ35MP. • Supports Intel® Core™2 Quad and Intel® Core™2 Duo processors and Intel® vPro™ processor technology. Intel® Desktop Board DQ35JO quick reference guide including specifications, features, pricing, compatibility, design documentation, ordering codes, spec codes. Product: Intel Desktop Board DQ35JO Provided Although the board comes in a mATX form factor doesn't mean it's short on features. ...

#09 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z